Metal roofing in Dallas

Standing seam and metal panels built for the Dallas climate

Metal Roofing in Dallas Built for Hail, Heat, and High Winds

Metal roofing in Dallas is the long-life answer for a Dallas home: standing seam panels with concealed fasteners that shed hail and heat, or exposed-fastener panels for a lower cost. Either way, the roof is only as good as the details — valleys, penetrations and eaves — and we build those the same way on every metal job.

Open 24 hours, every dayItemised written quotePhotos at every stage
Call firstTell us about the roof — pitch, size, material you have in mind — and what the home looks like
Safety before speedWe check the deck and the structure before any material is ordered
Diagnose the causeWe plan the system around the pitch, the panels and the ventilation
Approve the workYou see the written scope before anything is cut or seamed

What's included

What metal roofing includes

A metal roof is a system: the panels, the clips, the underlayment, the flashing and the ventilation — each part fitted to the roof, each detail finished in metal.

01

Standing seam systems

Panels with concealed fasteners, seamed together on site. No screw holes through the face, nothing to work loose in Dallas heat, and a roof that lasts decades.

02

Exposed-fastener systems

Corrugated and ribbed panels with screws through the face, at a lower cost. A solid choice for garages, additions and outbuildings, and for roofs where the budget decides.

03

Copper and specialty metals

Copper roofing and copper flashing for homes where the material is part of the design. Copper weathers to a patina and lasts longer than any other metal.

04

Decking checked first

The deck is inspected for damage and fastening before any panel goes on. A metal roof on a bad deck is a metal roof that fails early.

05

Details done in metal

Valleys, chimneys, skylights and vents are flashed in metal to match, with laps that run water over the joint. Metal roofs leak at the details, so the details get the most attention.

06

Permit and final inspection

Dallas requires a permit before any new roof covering is applied, and a final inspection once the work is complete. The permit application lists where debris will go, and the final inspection follows proof of disposal.

Service overview

What metal roofing in Dallas actually involves

Metal roofing in Dallas is the installation, repair and replacement of standing seam and exposed-fastener metal roofs on homes and commercial buildings. Metal lasts longer than shingles in Dallas heat, reflects more sun, and takes hail better — and it asks for careful detailing at every valley, chimney and vent.

The choice that matters most on a metal roof is the fastening: standing seam panels with concealed fasteners, or exposed-fastener panels with screws through the face. Standing seam costs more and lasts longer, because there are no screw holes to work loose in Dallas heat. The second choice is the profile and the colour, and the third is the detail work — valleys, penetrations and eaves — where metal roofs leak when they are done badly. Read the metal-vs-shingle guide on our blog. Read the best-materials guide on our blog.

Fastening is the differenceStanding seam panels are held by clips that let the metal expand and contract with the heat, with no screw holes through the face. Exposed-fastener panels are held by screws through the face, which work loose as the metal moves. The fastening is the difference between the two systems.
Metal handles hail and heatA metal roof reflects more of the Texas sun than a dark shingle roof, and the panels shed water fast in heavy rain. Large hail can dent the panels, but it rarely breaks through them — which is why metal is a hail answer for Dallas.
Check the district rules firstSome conservation districts in Dallas restrict visible roofing materials, and a standing seam roof is a visible change. We check the district rules before recommending a metal roof on a home in a conservation district.
Roofer seaming standing seam metal panels on a Dallas roof
How we workWe verify the cause, compare realistic options, and confirm the work before we leave.

The service timeline

What to expect on a metal job

The sequence is the same on every metal installation, and it is what makes the roof watertight.

01

Inspection

We walk the roof, check the deck and measure the slopes, and talk through the system — standing seam or exposed fastener — and the metal. You get photos and a written scope.

Stage 1
02

Scope

The written scope names the panel system, the metal, the colour, the flashing details and the ventilation, so the job is agreed before any panel is ordered.

Stage 2
03

Preparation

The deck is checked and prepared, the underlayment is laid, and the panels are cut and folded to fit the roof — valleys, eaves and penetrations measured, not guessed.

Stage 3
04

Install

Panels are laid and seamed, clips set to let the metal move, and flashing installed at chimneys, walls, skylights and vents. Ridge caps finish the system.

Stage 4
05

Cleanup and walkthrough

Offcuts collected, the ground swept with a magnet, and a walk of the finished roof with you. You receive the photos and paperwork for the job.

Stage 5

Tools & methods

Tools and methods we use on your metal roof

Metal work is mostly seaming and folding — the tools are for making panels fit exactly, not for forcing them.

01

Seaming tool

Closes the standing seam by hand or machine, folding the panel edges into a watertight joint with no exposed fasteners.

02

Panel brake and shears

Cuts and folds panels and flashing to fit each valley, chimney and eave exactly, instead of forcing a stock piece into place.

03

Clip fasteners

Hold the panels to the deck while letting them expand and contract with the heat — which is what stops the fasteners working loose.

04

Fall protection harness and roofing ladder

Keeps every installer tied off on steep metal pitches, which are slicker than shingle roofs and need the protection more.

05

Moisture meter

Checks the deck for hidden damp before panels go on, so wet sheathing is never sealed under a metal roof.

06

Butyl tape and sealant

Seals the laps and the penetrations where the detail calls for it, so the metal roof stays dry at every joint.

Use cases

When Dallas homeowners call us for metal

These examples show how metal work is planned around the fastening and the details.

Standing seam metal roof on a Dallas home
Standing seam on a North Dallas modern homeA modern home in North Dallas with a charcoal standing seam roof, concealed fasteners, and copper flashing at the chimney. The panels were seamed on site, the valleys were built with wide metal, and the eaves were finished with a continuous drip edge.

Metal over shingles in East Dallas

A metal roof installed over a single sound layer of shingles, with the deck checked first and the battens set to carry the new panels. The work was planned around the 2021 code, and the old shingles stayed in place only where the deck was sound and the total coverings stayed within the limit.

Metal repair in Oak Cliff

A standing seam panel section damaged by a fallen limb, with the seam torn open. The damaged panels were replaced and re-seamed, the clips beneath them checked, and the rest of the field walked for the same clip damage.

Problems we solve

Problems a metal roof solves for Dallas homes

Most metal calls are one of these four. Each one starts with the same question: which system, and which details?

ISSUE

Shingles failing every decade

A metal roof outlasts shingle cycles in Dallas heat. We scope the system — standing seam or exposed fastener — and the details that make it last.

SIGN

Hail bruising the field

Metal sheds hail better than shingles. Large hail can dent it, and dented panels are replaced and re-seamed, not patched over.

SYMPTOM

Leaks at valleys and penetrations

Metal roofs leak at the details, not the field. Valleys, chimneys and vents get wide metal, proper laps and new flashing.

ALERT

Hot attic in summer

A light-coloured metal roof reflects more heat, and balanced ventilation moves the rest out of the attic. Both are sized to the roof.

Cost factors

What shapes the cost of a metal roof in Dallas

PANEL SYSTEM, METAL, SIZE AND DETAILS SET THE SCOPE

Phase 01

Panel system

Standing seam with concealed fasteners costs more than exposed-fastener panels, and lasts longer — the fasteners are the difference.

Phase 02

Metal choice

Steel, aluminium and copper each carry different material costs and different lives. Copper costs the most and lasts the longest.

Phase 03

Roof size and details

Square footage drives the panels, and chimneys, valleys, skylights and dormers each add flashing and seaming work.

Customer reviews

What Dallas Homeowners Say

5.0★★★★★41 Google reviews
★★★★★
“I would highly recommend this roofing company to anyone in Dallas who needs roof repair or a full roof replacement.”
MK
Mandy KramerGoogle review · 4 weeks ago

Questions before we arrive

Metal roofing questions Dallas homeowners ask

Metal Roofing
Call (469) 960-7533
Standing seam or exposed-fastener metal roof?

Standing seam is the premium system: panels with concealed fasteners, seamed together, that last decades and shed Dallas hail well. Exposed-fastener panels are the budget option, with screws through the face that need checking over time. The choice depends on the roof, the budget, and how long you plan to stay in the home.

Is a metal roof good for Dallas heat and hail?

A metal roof reflects more heat than a dark shingle roof, which helps in a Dallas summer, and the seams shed water well in heavy rain. It handles hail better than shingles, though large hail can dent it. The trade-off is the cost and the sound of rain on metal, which some homeowners notice and others do not.

Can a metal roof go over my old shingles?

It can be, where the deck is sound and the total number of roof coverings stays within the Dallas limit of two. We check the deck first and plan the install around the code. Where the deck is damaged or the roof already carries two layers, the old roof comes off.

Does a metal roof need a permit in Dallas?

Yes. Dallas requires a permit before any new roof covering is applied, under City Code Chapter 52, section 301.4.6.3. The application lists where debris will go, and a final inspection follows once the work is complete and proof of disposal at a city landfill or transfer station is submitted.

Ready when you are

Get your metal roofing Dallas TX quote

An inspection, photos, and an itemised written quote for the metal roof as scoped. Call (469) 960-7533 and tell us about your home.

Metal Roofing

Talk with the local team

Request Metal Roofing

Call us at (469) 960-7533 or send a message and we will get back to you. We are open 24 hours, every day. Tell us about the roof and the look you want, and we will give you a straight answer on what it needs.

3919 Cedar Springs Rd, Dallas, TX 75219Main office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now